Remotec ZTS-100 V2.04 Manual de usuario

ZTS-100Z-ThermostatUSER MANUAL

ZTS-100 Z-Thermostat OperationsThe following section will guide you through the set up processes for your ZTS-100. Different listening nodes are able

Description of Function KeysNormal Operation ModeChange Operation ModeNote 1: In Heat mode => it displays "HEAT" if ELECTH is selected.=&

Select Fan ModeSelect Program Mode:LCD indicationStep Procedure / DescriptionPress "Fan" key once to change the Fan mode:FAN AUTO -> FAN

Override/Permanent OverrideNote 1: Override/Permanent Override is only available in HEAT, COOL or AUTO mode.LCD indicationStepAMMOFAN AUTOProcedure /

Setting Mode (Set Day, Clock, 12/24 hour, F/C, Swing and Differential)Setting ModeSetting Mode Key DescriptionSymbolIncrease value / Toggle selectionD

LCD indicationStepMOProcedure / DescriptionDay will keep flashing, press Up/Down key to set day from MO-SU.2AMMOPress "Prog" key once to con

Temperature Scale selection (for SIMPLE mode)LCD indicationStepMOProcedure / DescriptionPress "Prog" key once to confirm the setting and it

Setting ScheduleDefault Schedule:LCD indicationStep Procedure / DescriptionPress and hold "Prog" key for 2 seconds to entry the setting sche

LCD indicationStep Procedure / DescriptionPress "Prog" key once to confirm the setting and it will go to event mode.Press Up/Down key to sel

Z-Wave Add (Inclusion) / Delete (Exclusion) ModeLCD indicationStep Procedure / DescriptionPress "Prog" key once to confirm the setting and i

Table of ContentsIntroduction 2Features list 3Glossary 4Physical Installation and Wiring 5Installation Location 6Wiring 6Jumper Settings for ELECTH

Note 1: This icon is represent the ZTS-100 has been added into the Z-Wave network. Please perform the Delete (Exclusion) before adding into

Important: It is not allow changing ZTS-100 operation mode by change of power source. It is need to follow the above steps to change ZTS-100 operatio

Delete (Exclusion) ZTS-100 from Gateway / Controller Z-Wave networkSupport Association Command ClassZTS-100 support 2 association groups, each associa

Z-Wave Configuration CommandParameter value rangeParameter Number Definitionsoo0x01 = 0.5 C / 1 Fo o0x02 = 1.0 C / 2 F (default)oo0x03 = 1.5 C / 3

Filter CounterPress and hold "Mode" key to set the alert time for the filter usage."Target" icon will be shown on screen and flash

Reset ZTS-100 to Factory Default SettingsBattery Low IndicationLCD indicationStep Procedure / DescriptionPress and hold "Fan" + "Mode&q

Defrost IndicationOut of Temperature Range IndicationEnergy Saving ModeLCD indicationStep Procedure / DescriptionDEFROST icon will be displayed at Hom

Advanced Recovery IndicationShort Cycle Start Up ProtectionTo protect the compressor / Heat pump, those outputs forced off until 3minutes count down f

Frequently Asked QuestionsQ Why won't my ZTS-100 work with the Z-Wave devices I purchased from another country?A Due to different countries regul

COOL Mode: thermostat controls the temperature according to the following diagramooExample for Cooling: (Set point = 80 F, Swing = 1 F)oo=> Cooler

ZTS-100 Z-ThermostatIntroductionWelcome to the Z-Wave world of home automation, your ZTS-100 Z-Thermostat (Figure 1) is a comfort control master that

Technical SpecificationsModel no.BW8030US (ZTS-100US)BW8030AU (ZTS-100AU)BW8030EU (ZTS-100EU) RF frequency908.4MHz (US) (ZTS-100US)921.4MHz (AU) (ZTS-

Checking AccessoriesAfter opening the cover of the packaging box, check that the following accessories are included. - ZTS-100: Z-Thermostat- Screw +

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These lim

Features ListHVAC System Type Compatible: - Standard (gas/electric) or Heat PumpMultistage System Compatible: - Standard HVAC Systems: 2 stage heating

GlossaryDevices and nodes are all terms to describe an individual Z-Wave device. These are all interchangeable when setting up your Z-Wave network.Add

Physical Installation and WiringA controller containing network information about other devices within the network and is used for controlling devices

Installation Location:The Thermostat is restricted to be used in indoor only. It should be mounted on an inner wall about 1.5m above the floor at a po

When wiring split systems, wire the heating systems "24Vac Power" (red wire) to the ZTS-100 "RH" terminal, and wire the cooling sy

Jumper Settings for ELECTH-HPUMP and HE-HG:Mounting:1. Open the ZTS-100 by pushing the hook (Figure 5)2. Install AAx4pcs batteries if using battery po