Remotec ZFM-80 Manual de usuario descargar pdf

Single switch (connected with input AC power source for the

load)

External Switch

ZFM-80US provides an option to user that can add an

external switch to control the On/Off function. ZFM-80US

can be placed into the switch box with external wall

switch cover. User can configure the external switch type

through the configuration command

Configuration Command for External

Switch

Advanced function "Conditional trigger

for Fail Safe Application"

ZFM-80US provides an advanced function "Conditional trigger

for Fail Safe Application". It can turn on or turn off the relay if

ZFM-80US has not received any Z-Wave commands from a

specified Z-Wave Node ID and within a specified period. For

example: Z-Wave gateway can monitor a Z-Wave device status

and power on equipment if this Z-Wave device is out of service.

Figure 1

Single switch (connected with an external power source for the

load)

Figure 2

Warning

The resistive household appliance connected into the Z-Wave

controlled outlet on this module must not exceed 230Vac 10A or

120Vac 15A.

RELAY

(

LOAD

)

RELAY

(

LOAD

)

External switch

External

power source

Load

Introduction:

Thank you for choosing ZFM-80US Z-Wave control product. Our

Z-Wave enabled product allows user to remotely control resistive

household appliance, and make home control easy at low

installation / maintenance cost. You may begin with a few Z-

Wave enabled devices or build up a complete home automation

system with our products.

The ZFM-80US Fixture Switch Module is a Z-Wave enabled

device and fully compatible with any Z-Wave enabled network. It

allows remote On/Off control of specified resistive household

appliance. Each fixture switch module is designed to act as a

repeater, which will re-transmit the RF signal to ensure that the

signal is received by its intended destination by routing the signal

around obstacle and radio dead spots.

Glossary

Key Features:

- High output power

- Remote ON/OFF control via the Z-Wave controller

- Manual ON/OFF control with the front panel push button

- Support External ON/OFF key connects to the module

- Advanced function

Conditional trigger for "Fail Safe Application"

- Support Network Wide Inclusion (NWI) and Explore Frames

- Screw terminals for wires connection

- Flexible mounting structure - mount inside gang box or any

place

Wireless Control

ZFM-80US/DA065

Z-Wave Fixture Switch Module

USER MANUAL

Device /

Light /

Node

Z-Wave

Network

Inclusion

Exclusion

Network

Wide

Inclusion

(NWI)

Association

Devices, lights and nodes are all terms

to describe an individual Z-Wave device.

These are all interchangeable when

setting up your Z-Wave network.

A collection of Z-Wave devices is controlled

by primary and secondary controllers

operating on the same system.

A Z-Wave network has its own unique ID

code so that controllers not in the network

can not control the system.

Add a Z-Wave device to the network.

Delete a Z-Wave device from the network.

Network Wide Inclusion (NWI) enables

both end-user friendly, Plug and Play like

Z-Wave network installation as well as

professional installation scenario where

the inclusion process in terms of time will

be reduced significantly. NWI is a feature

supported by a new frame type named

Explorer which enables the Z-Wave

protocol to implement Adaptive Source

Routing.

Association is used to organize nodes in

different groups allowing the device to

identify the nodes by a group identifier.

The groups can also be copied to other

devices.

()

RELAY LOADNL

Product Overview:

Mount

Status LED

ON/OFF/PROG Push button

External switch (S/W)

Z-Wave controlled output (isolated relay, RL)

AC input (L = terminal for Live lead;

N = terminal for Neutral lead)

Installation:

DANGER! SHOCK HAZARD. Read and understand these

instructions before installing. This device is intended for

installation in accordance with the National Electric code and

local regulations in the United States, or the Canadian Electrical

Code and local regulations in Canada. It is recommended that a

qualified electrician perform this installation.

For indoor use only in a dry location. Retain instructions for future

use.

Step 1 WARNING: To reduce the risk of fire or electric shock,

install in a controlled environment relatively free of

contaminants. To avoid fire, shock, or death; turn off

power at circuit breaker or fuse and test that power is off

before wiring!

Step 2 Identifying your wiring application: refer to figure 1

and 2

NOTE: If the wiring in the wall box does not resemble

any of above configurations, consult a qualified

electrician.

Step 3 Connecting wires: refer to figure 1 or 2 and connect

the wires with correct symbols.

Use at less 75 C copper wire only and the stripped

wire end's length must be 9mm. The tightening torque

must be 3.5lb-in. (Make sure all wires are firmly fixed at

all terminals)

CAUTION : Risk of Electric Shock More than one disconnect

switch may be required to de-energize the equipment before

servicing.

S/W

External Switch

Parameter

Number

Set External switch type

Definitions

1 (0x01)

Parameter

Value

Disable External switch

Definitions

0 (0x00)

1 (0x01)

2 (0x02)

3 (0x03)

4 (0x04)

Type A:

Tact switch (normal open)

Type B:

Tact switch (normal close)

Type C:

Rocker switch

(short = On; open = Off),

default

Type D:

Rocker switch

(short = Off, open = On)

Example:

External switch

S/W

1 2

Indice de contenidos

Pagina 1 - USER MANUAL

Single switch (connected with input AC power source for the load)External Switch ZFM-80US provides an option to user that can add an external switch t

Pagina 2

Restoring Factory DefaultsAll Configuration Parameters can be restored to their factory default settings by using your primary controller to reset the

Comentarios a estos manuales

Sin comentarios

Remotec ZFM-80 Manual de usuario

Busca en linea o descarga Manual de usuario para Control remoto Remotec ZFM-80. Remotec ZFM-80 User Manual Manual de usuario

Indice de contenidos

Comentarios a estos manuales

Relacionado con productos y manuales para Control remoto Remotec ZFM-80